|
|
|
Home > Air-Fuel Ratio, Oxygen, & Lambda Modules > LambdaCAN |
|
|
| Description: |
|---|
ECM's LambdaCAN Module is a powerful, "next-generation" wideband Lambda (and AFR, O2) measurement module with a CAN interface. In addition to providing outstanding measurement range and accuracy, LambdaCAN addresses the two principle sources of error with wideband sensor use: sensor aging and pressure sensitivity. All wideband sensors supplied are factory-calibrated and this calibration is stored in a memory chip in the sensor's connector. For best accuracy over the life of the sensor, calibration can be quickly performed using ambient air. This recalibration is stored in the memory chip and stays with the sensor. Sensors can be tested and recalibrated in a central location and distributed to users, ensuring consistent results throughout a large test facility. Pressure compensation (P-COMP™) improves accuracy at non-stoichiometric (i.e. λ ≠ 1) and non-atmospheric (i.e. P ≠ 101 kPa) conditions. For example, a pressure increase of only 34 kPa will cause an error of 0.58 λ at λ = 3. Pressure compensation eliminates this error and enables innovative applications such as %O2 measurements in intake manifolds. Pressure data is available on the CAN bus.
LambdaCAN will work with all NTK and Bosch-type wideband sensors. It is programmable for all fuel types (H:C, O:C, N:C ratios and H2). LambdaCAN outputs λ, AFR, %O2, pressure, and all sensor parameters including pumping current, resistance, and sensor age factor.
|
| Specifications: |
|---|
| Inputs: | 1 Wideband Lambda Sensor, 1 Pressure Sensor (optional) | | Ranges: | λ 0.4 to 25
AFR 6 to 364
F/A 0.003 to 0.167
φ 0.04 to 2.5
O2 0 to 25%
Pressure (optional) 0 to 517 kPa (0 to 75 psia) | | Accuracies: | λ, AFR, φ ± 0.6% (at stoichiometric), ± 0.9% (average, elsewhere)
%O2 ± 0.1% (absolute)
Pressure (optional) ± 5.2 kPa (± 0.75 psia) | | Response Time: | Less than 150 ms | | Fuel Type: | Programmable H:C, O:C, and N:C ratios, and H2 | | CAN: | High Speed according to ISO 11898 | | Configuration: | Via CAN Bus with Configuration Software. Programmable Node ID. | | Module: | 145mm x 120mm x 40mm, Environmentally Sealed | | Environmental: | Electronics -55 to +125°C, IP67
Sensor 850°C (maximum continuous) | | Sensor Cable: | 0.25m (sensors), +1m (standard), +2m (optional) | | Power: | 11 to 28 VDC, AC/DC (optional) | | Sensor Mounting: | 18mm x 1.5mm thread (wideband), 1/4" NPT (pressure) |
|
| Jump to Optional Kits and Parts |
|---|
| Related Downloads: |
|---|
 LambdaCAN Brochure (US) (10-13-2008, 221KB)
LambdaCAN Brochure (Eur) (10-13-2008, 150KB)
Aluminum Block Brochure (27KB)
Exhaust Probe Brochure (104KB)
Vboost Power Supply Brochure (165KB)
ETAS INCA Setup Guide (1052KB)
ATI VISION Setup Guide (504KB)
 ECM CAN Configuration Tool (v4.48.08, 28987KB)
Firmware Update Procedure for Modules (225KB)
| | Ordering Information, Complete Kit P/N: LambdaCAN |
|---|
The complete kit includes the following parts:
| Item | Description | P/N | Qty | Photo |
|---|
| 1. | LambdaCAN Module | 02-01 | 1 |  | | 2a. | NTK 6mA O2 Sensor, or | 05-01 | 1 |  | | 2b. | Bosch LSU4.2 O2 Sensor, or | 05-02 | 1 |  | | 2c. | Bosch LSU4.9 O2 Sensor, or | 05-03 | 1 |  | | 2d. | NTK 4mA O2 Sensor | 05-04 | 1 |  | | 3. | Eurofast 12mm Cable, 2m | 09-02 | 1 |  | | 4. | Flexi-Eurofast Cable, 0.3m | 09-04 | 1 |  | | 5. | Eurofast "T" Connector | 09-05 | 1 |  | | 6. | Eurofast Termination Resistor | 09-06 | 1 |  | | 7. | Lambda/NOx/NH3 Cable, 1m | 10-02 | 1 |  | | 8. | DC Power Cable, DB9F, Banana Plugs | 11-02 | 1 |  | | 9. | 18mm x 1.5mm Mild Steel Boss and Stainless Steel Plug | 12-02 | 1 |  | | 10. | 5200 Series Manuals & Configuration Software CD
This PC-based software allows configuration of CAN communication, calibration of sensors, and data logging. Requires Kvaser, Vector, or Peak USB-to-CAN adapter. (Available from ECM, see P/N 13-02 below) | 13-01 | 1 |  |
Optional Kits and Parts:
For pressure compensation, these additional items are included:
| Item | Description | P/N | Qty | Photo |
|---|
| 1a. | Pressure, Type KP, 0-75 psia, 1/4" NPT (USA), or | 07-05 | 1 |  | | 1b. | Pressure, Type KP, 0-517 kPa, 6mm (Metric) | 07-06 | 1 |  | | 2. | Module Y Cable | 10-21 | 1 |  | | 3. | Pressure Cable (4-terminal), 1m | 10-04 | 1 |  | | 4a. | Pressure Line Assembly, 1/4" NPT Tubing/Hose/Fittings, 28" Length (USA), or | 12-08 | 1 |  | | 4b. | Pressure Line Assembly, 6mm Tubing/Hose/Fittings, 711mm Length (Metric) | 12-11 | 1 |  |
Accessories:
| Item | Description | P/N | Qty | Photo |
|---|
| 1. | CAN-to-USB Adapter | 13-02 | 1 |  | | 2. | AC/DC Power Supply w/ CAN Tap, Universal, 24VDC 4.2A
(Requires P/N 11-17 for use with CAN-to-USB adapter) | 04-01 | 1 |  | | 3. | Deutsch DTM3M to DB9F | 11-17 | 1 |  | | 4. | DC Power Cable, DB9F, Spades | 11-01 | 1 |  | | 5. | DC Power Cable, DB9F, Banana Plugs, 1m | 11-36 | 1 |  | | 6. | Vboost Power Supply (Boosts supply voltage to avoid dropout situations) | 04-02 | 1 |  | | 7. | AC/DC Power Supply, 120VAC In, 15VDC 15A Out, 4.5" x 6" 10", 13lbm
(Up to 4 Modules and 2 Display Heads) | 04-04 | 1 |  | | 8. | AC/DC Power Supply, 120VAC In, 24VDC 15A Out, 7.5" x 7.0" x 2.5", 4lbm
(Up to 8 Modules and 4 Display Heads) | 04-03 | 1 |  | | 9. | AC/DC Power Supply, 120VAC In, 15VDC 60A Out, 6.75" x 10.5" x 11.5", 33lbm
(Up to 16 Modules and 8 Display Heads) | 04-05 | 1 |  | | 10. | Eurofast 12mm Cable, 10m | 09-03/10 | 1 |  | | 11. | Lambda/NOx/NH3 Cable, 2m | 10-03 | 1 |  | | 12. | Lambda/NOx/NH3 Cable, 3m | 10-37 | 1 |  | | 13. | Pressure Cable (4-terminal), 2m | 10-05 | 1 |  | | 14. | Pressure Cable (4-terminal), 3m | 10-40 | 1 | | | 15. | Lambda Sensor Extension Cable with Midpoint Lemo Connectors (Controller Side) | 10-42A | 1 |  | | 16. | Lambda Sensor Extension Cable with Midpoint Lemo Connectors (Sensor Side) | 10-42B | 1 |  | | 17. | Eurofast Hub Block, 8-channel | 09-08 | 1 |  | | 18. | Termination Resistor for Hub Block | 09-09 | 1 |  | | 19. | 2m Hub Power/Eurofast Harness | 11-10 | 1 |  | | 20. | 1/4" UNC Module Stacking Standoff
(Use to mount and stack ECM CAN modules. One kit mounts/stacks two
modules. Each additional kit mounts/stacks an additional module.) | 12-25 | 1 |  | | 21. | dashCAN+ | DASHP | 1 |  | | 22. | dashCAN2 | DASH2 | 1 |  | | 23. | dashCAN | DASH | 1 |  | | 24. | Aluminum Mounting Plate for 8-Ch Block and Modules (16" x 10" x 0.16") | 12-42 | 1 |  | | 25. | 19" Rackmount Panel (holds up to 4 display heads or 4 dashCANs) | 12-01 | 1 |  | | 26. | 18mm x 1.5mm Mild Steel Boss and Stainless Steel Plug | 12-02 | 1 | | | 27. | 1/4" NPT Mild Steel Boss and Brass Plug (USA) | 12-05 | 1 |  | | 28. | 1/4" ISO Mild Steel Boss and Brass Plug (Metric) | 12-12 | 1 | | | 29. | Aluminum Remote Sensor Mounting Block (18mm x 1.5mm, 5 x 1/4" NPT) | 12-18 | 1 |  | | 30. | Individual Cylinder Exhaust Probe (18mm x 1.5mm) (USA) | 12-19 | 1 |  | | 31. | Individual Cylinder Exhaust Probe (18mm x 1.5mm) (Metric) | 12-20 | 1 | |
|
|
|
|
(408) 734-3433
;)
;)
;)
;)
;)
;)
;)
![](javascript:popup('pop-img.asp?ti=P/N: 09-05&src=img/parts/09-05.jpg&desc=Eurofast "T" Connector', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
;)
;)
;)
;)
', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 07-05&src=img/parts/07-05.jpg&desc=Pressure, Type KP, 0-75 psia, 1/4" NPT (USA)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
;)
, 1m', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 12-08&src=img/parts/12-08.jpg&desc=Pressure Line Assembly, 1/4" NPT Tubing/Hose/Fittings, 28" Length (USA)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
;)
', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
;)
;)
;)
', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 04-04&src=img/parts/04-04.jpg&desc=AC/DC Power Supply, 120VAC In, 15VDC 15A Out, 4.5" x 6" 10", 13lbm<br />(Up to 4 Modules and 2 Display Heads)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 04-03&src=img/parts/04-03.jpg&desc=AC/DC Power Supply, 120VAC In, 24VDC 15A Out, 7.5" x 7.0" x 2.5", 4lbm<br />(Up to 8 Modules and 4 Display Heads)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 04-05&src=img/parts/04-05.jpg&desc=AC/DC Power Supply, 120VAC In, 15VDC 60A Out, 6.75" x 10.5" x 11.5", 33lbm<br />(Up to 16 Modules and 8 Display Heads)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
;)
;)
;)
, 2m', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
, 3m', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
;)
;)
;)
![](javascript:popup('pop-img.asp?ti=P/N: 12-25&src=img/parts/12-25.jpg&desc=1/4" UNC Module Stacking Standoff<br>(Use to mount and stack ECM CAN modules. One kit mounts/stacks two<br>modules. Each additional kit mounts/stacks an additional module.)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 12-42&src=img/parts/12-42.jpg&desc=Aluminum Mounting Plate for 8-Ch Block and Modules (16" x 10" x 0.16")', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 12-01&src=img/parts/12-01.jpg&desc=19" Rackmount Panel (holds up to 4 display heads or 4 dashCANs)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 12-05&src=img/parts/12-05.jpg&desc=1/4" NPT Mild Steel Boss and Brass Plug (USA)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 12-12&src=img/parts/12-05.jpg&desc=1/4" ISO Mild Steel Boss and Brass Plug (Metric)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
![](javascript:popup('pop-img.asp?ti=P/N: 12-18&src=img/parts/12-18.jpg&desc=Aluminum Remote Sensor Mounting Block (18mm x 1.5mm, 5 x 1/4" NPT)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
 (USA)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)
 (Metric)', 'popimg', 'width=400, height=300, resizable=1, scrollbars=1');)